Flying Leathernecks

Vinyl Mask..

Vinyl Mask..

3D ResinThis set includes two (2) XM158A1 Rocket Launchers.The Launcher was a seven-tube, reloadable, reusable, repairable 2.75" rocket launcher M158A1 was a variant of the M158 that included a modified hardback mount..

3D ResinThis is a two piece 3D printed set of the SATCOM antenna mounted to the top of the main rotor mast on the UH-1Y Helicopter.Simply glue the antenna to the top center of the base, paint and attach to your model. Parts come ready to install with no clean up required...

3D ResinSet of four (4) 3D printed launchersIn January of 1987, AAC-829 was introduced and by May of 1988, over 6500 launchers had been modified to LAU-7/A-6.Over the course of the next several years, numerous AAC's changed the designation of the launcher to B/A, A-7, B/A-1, as well as a few oth..

3D ResinThis set includes two empty LAU-68F/A pods. The F/A is 11 inches longer than the LAU-68D/A and is used exclusively with the 2.75 APKWS rockets. Pod is used by the F/A-18, AV-8B, AH-1Z, UH-1Y, A-10, F-16 and a number of other aircraft.Pods are 3D printed and come ready to paint and attach t..

3D Resin..

3D ResinThis set contains two (2) LAU-10 5.00" rocket pods with empty tubes. Tubes are hollow the whole length of the pod.Designed by Matt Farrow of Shrunk Craft..

3D ResinThis set includes four (4) octagon shaped drip pans commonly found under aircraft, both on the flightline and in hangar spaces. Great for use in dioramas to add a little bit more realism to your scene.Parts come as shown in photo. Very light sanding needed on one surface needed prior to pa..

3D ResinThis set includes six (6) SATCOM Antenna with short mount found on a number of Helicopters. Use fine sprue cutters to remove part from support and lightly sand base smooth. Attach using super glue (CA)...

3D ResinAN/ALQ-144, ready to paint and attach to your model.For AH-1W, AH-64A/D/E, UH-1N, H-60, OH-58, VH-3D and OV-10..

3D ResinThis set includes 6 buckets that can be used to replace those found in kits that may be under detailed...

3D ResinThis set includes six (6) buckets that can be used in a diorama setting (ordnance loading evolution) or to replace kit parts...

Vinyl Detail..

3D ResinThis detailed TSS is a direct replacement for the kit parts. Simply detail paint and install.Use sprue cutters to remove turret from supports and lightly sand support nibs smooth. It may be necessary to remove the locating tabs from kit parts C59 and C60..

3D ResinThe FMV Mod fitted to the tail boom of the AH-1Z and UH-1Y allows grounds units to see what the aircrew sees through the aircraft's FLIR.Designed for the Academy kit..

3D ResinThis set includes four (4) ADU-299 Adapters. These are used to allow aircraft to carry the LAU-7 missile launcher on stations not normally designed to carry that launcher...

This set includes two (2) thermally protected Mk-83 1000lb bombs with conical fins and M904 nose fuses. 3D printed items come as shown in the photo...

This set includes two (2) thermally protected Mk-82 bombs with BSU-86 fins and MXU-735 Solid Nose Plugs3D printed items come as shown in the photo..

This set includes two (2) thermally protected Mk-82 bombs with BSU-86 fins and M904 fuzes3D printed items come as shown in the photo..

This set includes six (6) Mk-76 practice bombs..

This set includes two (2) LAU-7 launchers and is designed to be used with set FL18-1008 on the Hobbyboss AV-8B kit. Can also be used with the JSI 18th scale F-14 and F/A-18.Designed by Richard VanZandt..

This set includes eight (8) wing pylons, one (1) centerline pylons, two (2) aft pylon fairings, and seven (7) BRU-36 ejector racks.3D printed and designed by Richard VanZandt using photos and measurements provided by FLD, Simon Oakes, Robert Foster and David Sweetman..