Flying Leathernecks

This set includes four (4) GBU-16 laser guided bombs. For ease of alignment, while still being easy to paint, the guidance sections and warheads are printed together.** Due to slight variations in the printers used, it may be necessary to drill out the holes for the fins in the guidance section u..

This set includes four (4) GBU-12 laser guided bombs. For ease of alignment, while still being easy to paint, the guidance sections and warheads are printed together.** Due to slight variations in the printers used, it may be necessary to drill out the holes for the fins in the guidance section u..

This set includes four (4) GBU-12 laser guided bombs. For ease of alignment, while still being easy to paint, the guidance sections and warheads are printed together.** Due to slight variations in the printers used, it may be necessary to drill out the holes for the fins in the guidance section u..

This set includes two (2) fuel tanks, made up of four (4) parts each. The nose section, main body, tail cone and a key to line up the nose and main body.Lightly sand the forward mating surface of the main body to remove the print support nibs, insert key, then attach nose section. Light sanding of..

The FPU-6/A Oval Fuel Tank was developed for the F/A-18A/B Hornet in 1978 and used on the FSD aircraft, as well as a few fleet Hornets into the mid 1980's. It was phased out due to fatigue anomalies caused by the oval configuration.This set includes two hollow tanks that require assembly. Some li..

Designed by P. Haupt, these doors provide better, and more accurate details over the kit parts.There are four (4) pieces in this set. Second aft strut door is to show antenna detail on outside surface...

Waterslide Decals printed by Microscale (Insert printed by Cartograf). 8.5 x 11.0 inch sheet..

Waterslide Decals printed by Microscale (Insert printed by Cartograf). 8.5 x 11.0 inch sheet..

Waterslide Decals printed by Microscale (Insert printed by Cartograf). 8.5 x 11.0 inch sheet..

Designed by P. Haupt, these doors provide better, and more accurate details over the kit parts.There are six (6) pieces in this set...

Wheels designed to fit the Hasegawa F/A-18A/B/C/D Hornet Kits..

Wheels designed to fit the Kinetic F/A-18A/B/C/D Hornet Kits..

This set includes correctly shaped and sized LEX Fence parts applicable to all 1/48 F/A-18A/B/C/D Hornet kits...

All NEW design HUD assembly for use with the Hasegawa or Kinetic kits. Complete unit is 3D printed and comes ready to install after a small modification to the kit parts.Includes die cut 'glass' in .005 clear styrene..

This set includes a total of four (4) tail stiffening plates commonly found on F/A-18A and F/A-18A+ Hornets. The four plates will complete two (2) models.3D printed, the plates have all of the rivet and screw fasteners visible. Simply remove from the support, sand the small attachment points smoot..

All NEW design HUD assembly for use with the Hasegawa or Kinetic kits. Complete unit is 3D printed and comes ready to install after a small modification to the kit parts.Includes die cut 'glass' in .005 clear styrene..

This set includes six (6) GPS Antenna found on the F/A-18 Hornet, EA-6B Prowler, CH-46E and several other aircraft.3D printed, parts come as shown and are very easily removed from the supports using sharp sprue cutters or X-Acto type blade. Use Super Glue (CA) to attach to kit...

Designed specifically for the Tamiya F-4B, this new 3D printed fin cap allows the modeler to build F-4B's that were fitted with the AN/APR-25 antenna.Fin cap comes removed from the print supports and only needs a few swipes with a sanding stick to remove the remaining nubs. Simply glue in place an..

This part is designed to be used with Bullseye Model Aviation Decal Sheet 48-017 and Furball Aero-Design Decal Sheet 48-076 when building the VF-14 and VF-32 options.Mastered by Richard VanZandt, it is a drop in replacement for kit part P18/P19...

Designed specifically for the Tamiya F-4B, this new 3D printed fin cap allows the modeler to build early F-4B's, as well as USAF F-110 with little to no effort.Fin cap comes removed from the print supports and only needs a few swipes with a sanding stick to remove the remaining nubs. Simply glue i..

*** NOTE *** This sheet does NOT include the mask for the bat!Waterslide Decals printed by Microscale (Insert printed by Cartograf).5.5 x 8.5 inch sheet..

This set includes two (2) main and two (2) nose wheels for Kinetic's 1/48 EA-6B, E-2C and C-2A kits.Due to variations in the printing process, as well as very slight differences in the kits landing gear, it may be necessary to enlarge the mounting holes on each wheel using a small drill bit.Whee..

Waterslide Decals printed by Microscale (Insert printed by Cartograf). 5.5 x 8.5 inch sheet..

This set provides correctly sized and detailed wing fold hinge covers for the Kinetic or Italeri (Kinetic plastic) EA-6B Prowler kits.A quick and light sanding of one edge to remove the support nibs is all that is needed. Simply pop into place and glue...