Hypersonic Models

Stabilator for all types of F-4 Phantom that used the unslotted stab. For both the Hasegawa and Academy kits. Includes separate PE pivot cover plates and stiffener "fishplates" (for Air Force variants). The stabs can be used as a drop fit replacement for the kit parts or, with some work on the kit p..

Corrected tail surfaces (stabilisers, elevators and rudder) for the Kitty Hawk FJ-2 Fury (and early FJ-3). The FJ-2 kit only contains the ribbed elevators/rudder, which is correct for an FJ-3 and very late FJ-2's after transfer to the Reserves. FJ-2's in service (as well as early FJ-3's) had smooth-..

A pair (2) of early McDonnell type 370gal wing drop tanks for F-4 Phantoms. Mainly applicable for early Phantoms such as F4H-1/F-4B/C/(D), but seen as late as 1973 on an F-4J. Separate, handed pylons are included. The tanks are cast in hollow halves that are very easy to clean up and assemble...

This is an upgrade set for Zoukei Mura Phantoms. As per the kit, the stabilators can only be mounted in one (or two) position(s). With this set, you can set the stabilators in any position of your choice and improve the detail on the stabilator pivot cover plates as well. Also included are the reinf..

Stabilator for all types of F-4 Phantom that use the slotted stab. For both the Hasegawa and Academy kits. Includes separate PE pivot cover plates and stiffener "fishplates" (for Air Force variants). The stabs can be used as a drop fit replacement for the kit parts or, with some work on the kit plas..

F-4 Phantom outer pylons, Air Force type, 1:48, designed for the Zoukei Mura line of kits. The pylons have the correct outboard angle built in and come with separate sway brace pins so stores can be mounted at correct angles, either canted in line with the pylon or perpendicular to the ground...

This is a set of aft fuselage half parts that correct the shape error on the engine shoulders of the Zoukei Mura short nose Phantoms. in addition to the re-shaped geometry, some surface detail has been improved. Please note that this is not a drop-fit replacement set. Cutting of the fuselage is requ..

F-4 Phantom C/L pylon, 1:48, for the Zoukei Mura line of kits. The pylon fit on and into the detail moulded onto the ZM lower wing surface. It comes with two sets of separate pins - one for the larger stabiliser pins and the smaller sway brace pins that connect to the stores to be mounted...

Detail parts for the inner canopies on F-4 Phantoms. The set comprises of resin and PE parts for windscreen, forward-, centre- and rear canopies and includes canopy actuator jacks, safety uplocks (optional installation), detailed downlocks, forward and rear compasses and various detail parts for the..

Corrected A/C air intakes for Academy's F-4 Phantom series (F-4B, C and D so far). Drop fit resin replacement. All it takes is a little superglue and a swipe of filler to blend it in...

This is a set of two SR-1 seats for the new Revell 1:48 SR-71. The seats are very accurate in dimension and detail and have been fully CAD designed. The two seats in the set are not identical in the draping/positioning of the belts and hoses. One modification to a detail on the seat was made to adap..

This is a backdate set for Kinetic's F-104A/C kit to build an early F-104A with the downward firing C-1 ejection seat. The set includes parts from the F-104A Late set (lower fuselage insert, alternate hot air exhaust panel, L-brackets) plus the C-1 seat, ejection rails, rear cockpit bulkhead, forwar..

This is a centreline pylon for Kinetic's F-104 series, suitable for variants from C through to S. The item is 3D printed and packed with detailed features. The outer sway braces are fixed, while the two centre pads are separate pieces that can be adjusted to match the loadout being mounted. The pylo..

This is a backdate set for the (new tool) Kinetic F-16A kit and contains parts to build Block 1,5 and 10 aircraft. The set includes small stabilators with thin static wicks, early instrument panel and coaming, Environment Control System (ECS) exhaust panel, RWR and rectancular UHF antennas. The stab..

This conversion set includes the AN/ANQ-126 fairings for the intakes (with mounting holes to match Tamiya's moulded-on pins), a fin cap with the correct sensor bulge for the N model, a new RIO instrument panel and an external rear view mirror. Further N specific parts are already included in the Tam..

Full injection moulded plastic kit of one AG-330 start cart for the famous Blackbird family of planes (A-12, YF-12, M-21 and SR-71). Optional parts for both an early "Buick" powered, or the later "Chevy" powered cart are included. The starter probe can be built retracted or extended. Photo etched de..

This is a set of two individually detailed Martin Baker Mk. GRU5 seats in 1:48 for A-6A, EA-6A and A-6E Intruders (used until about the mid 70s, when replaced by the GRU7), designed and sized for the Hobby Boss cockpit. I can't say if it will fit the Revell EA-6A. The belt and hose arrangement is di..

This is a set of full-length and correctly angled jet exhaust tailpipes for the A-6 Intruder family (A-6A, A-6E, A-6E TRAM, EA-6A). It contains detailed, thin-edged nozzles as well as detailed J-52 engine end with guide vanes and probes. The set is designed for the HobbyBoss Intruder kits (and the i..

This is a full-length resin exhaust and nozzle set with the specific detail for EA-6B Prowlers which have an upgraded engine and different nozzle to the A-6 Intruder family. The instructions are based on fitting it to the Kinetic/Italeri kits, but the modeller may be able to adapt them to the Revell..

This is an early, plain fin cap without any RHAW or ECM pods as used on early F-4B (and C). Designed as a drop in replacement part for the Tamiya kit...

These are 3D printed face curtain handles for MB Phantom ejection seats. The handles are mainly designed for the Hypersonic Models Mk. H5 seats but can be used on other types (H7) and manufacturer's seats as well. The handles are 3D printed but from a slightly elasctic resin that doesn't break as ea..

This is an empty SR-71 brake chute bay with open doors, as commonly seen after landing. Designed specifically for the Revell kit. The set comes in four 3D printed parts: the main bay, a separate end cap (for easier painting) and separate doors. The door parts have mounting lips and recesses designed..

This set contains the parts needed to build an accurate late type F-104A from the Kinetic F-104A/C kit. "Late" means that it's an airframe that was converted to the upward firing C-2 seat. Therefore you can either use the kit supplied seat or one of the various available aftermarket options.The pa..

This is a set of highly detailed and appropriately proportioned stick/grip and throttle for the Kinetic F-104 kits in 1:48. The kit parts are both oversized and a bit sparse in detail. These 3D printed resin parts are drop-in replacements that fit right into the kit's mounting holes. The parts fit b..