Hypersonic Models

This set contains a pair of 1:72 outer wing pylons with weapons adapters for USN and USMC Phantoms (and some early USAF ones as well). Suitable for all brands of 1:72 Phantom kits...

This is a full-length resin exhaust and nozzle set with the specific detail for EA-6B Prowlers which have an upgraded engine and different nozzle to the A-6 Intruder family. The instructions are based on fitting it to the Kinetic/Italeri kits, but the modeller may be able to adapt them to the Revell..

This is an early, plain fin cap without any RHAW or ECM pods as used on early F-4B (and C). Designed as a drop in replacement part for the Tamiya kit...

Detail parts for the inner canopies on F-4 Phantoms. The set comprises of resin and PE parts for windscreen, forward-, centre- and rear canopies and includes canopy actuator jacks, safety uplocks (optional installation), detailed downlocks, forward and rear compasses and various detail parts for the..

These are 3D printed face curtain handles for MB Phantom ejection seats. The handles are mainly designed for the Hypersonic Models Mk. H5 seats but can be used on other types (H7) and manufacturer's seats as well. The handles are 3D printed but from a slightly elasctic resin that doesn't break as ea..

This is an empty SR-71 brake chute bay with open doors, as commonly seen after landing. Designed specifically for the Revell kit. The set comes in four 3D printed parts: the main bay, a separate end cap (for easier painting) and separate doors. The door parts have mounting lips and recesses designed..

This set contains the parts needed to build an accurate late type F-104A from the Kinetic F-104A/C kit. "Late" means that it's an airframe that was converted to the upward firing C-2 seat. Therefore you can either use the kit supplied seat or one of the various available aftermarket options.The pa..

This is a set of highly detailed and appropriately proportioned stick/grip and throttle for the Kinetic F-104 kits in 1:48. The kit parts are both oversized and a bit sparse in detail. These 3D printed resin parts are drop-in replacements that fit right into the kit's mounting holes. The parts fit b..

This is a set of highly detailed and appropriately proportioned stick/grip and throttle for the Kinetic F-104 kits in 1:48. The kit parts are both oversized and a bit sparse in detail. These 3D printed resin parts are drop-in replacements that fit right into the kit's mounting holes. The parts fit b..

This is a set of two aft canopy braces for Kinetic F-104 Starfighter kits. This part is applicable to all F-104 single seat variants and is not provided in any of the Kinetic's kits. The part is very delicate, but printed from slightly forgiving resin for safer support removal and handling...

A set of two Martin Baker Mk. H5 ejection seats for early F-4B, F-4C and F-4D Phantoms (until around 1970). Suitable for and tested with Academy, Hasegawa and Zoukei Mura kits. The seats have cast on seat belts which differ from each other...

This is a set of 3D printed B-26K (A-26A) Counter Invader / Nimrod wheels. For the ICM kit in 1:48. The mounting points are designed for a direct fit to the kit axles. The wheel hubs are loaded with fine and accurate detail, from valve stems to visible springs in the brake pads. The tyres have very ..

This is a TISEO pod for the Meng F-4E kit, 1:48. The pod parts are 3D printed and the glass is a cast clear resin piece. A paint mask is provided as well...

This is a set of Navy type outer wing pylons designed to fit the Zoukei Mura Phantoms (J and S). The set comes with separate sway brace pins so the modeller can adapt them completely free to the specific store and correct outboard angle (in case of MER or TER installed). The photos show the pylon bo..

Here is full set of resin wheels for Revell's 1:48 SR-71 kit. The wheels come with all correct detail, including brake detail and even the brake line connectors on the main wheel hubs. The anti-skid generator brackets are provided as delicate photo etch parts. The main wheels are NOT two identical s..

This is an upgrade set for the stabilator area of the Tamiya F-4 Phantom kit(s). It replaces the kit's overly thick stabiltor cover plates and guide tracks with much thinner and more detailed PE parts. At the same time, you will also install the kit's separate lower tail insert module early on. You ..

This is an IRST equipped chin (radome) pod for early F-4B's, specifically for the Tamiya kit. While not from the very start of production deliveries, F-4B's were fitted with this Infra-red Search and Track system from ca. 1962. The pod in the Tamiya kit is the late type, having a longer non-IRST for..

This is a set of two SR-1 seats for the new Revell 1:48 SR-71. The seats are very accurate in dimension and detail and have been fully CAD designed. The two seats in the set are not identical in the draping/positioning of the belts and hoses. One modification to a detail on the seat was made to adap..

A pair (2) of early McDonnell type 370gal wing drop tanks for F-4 Phantoms. Mainly applicable for early Phantoms such as F4H-1/F-4B/C/D, but seen as late as 1973 on an F-4J...

The early/narrow tyres in the Hasegawa kit are too wide. These new tyres are narrower, have deep tread detail and are very subtly bulged. Use these tyres with both the early and late style wheel hubs with all operators EXCEPT German, Italian and other Euro-NATO AF's that used the G model - or in oth..