Model Motorcycles

Kit contains: - chain with sprockets (precut and ready for painting), - front sprocket screw (printed on sprocket), - set of rear sprocket nuts (printed on sprocket)...

Set of 50 electrical wiring connector which will raise level of detail of your model on the next level. Kit contains: - 10 connectors of A type - 2 holes on each side (dim. 1 x 1.7 x 3 mm) - 10 connectors of B type - 4 holes on each side (dim. 1.7 x 1.7 x 3mm) - 20 connectors of C type - 1 hole on e..

Dzus type quick release fasteners with large rhomboid base (Type 2) at 1/12 scale, with a width of 3,6mm. Made in resin by 3D printing, they reproduce all the details, such as the mounting rivets. They are extremely thin, and have a 0.8mm diameter support rod for mounting, which will allow you to fi..

Dzus type quick release fasteners with rhomboid base (Type 1) at 1/12 scale, with a width of 3mm. Made in resin by 3D printing, they reproduce all the details, such as the mounting rivets. They are extremely thin, and have a 0.8mm diameter support rod for mounting, which will allow you to fix them w..

Kit contains: - clutch with visible discs, - clutch basket, - external cover with mounting holes corresponding to the engine block design, - set of screws (spare elements includes)...

Pre-cut paint mask in repositionable, low-adhesion paper, which fits over the transparent part of the dome (part E7) of the Tamiya kit to protect and correctly complete the painting process of its edge in black.Family: Masks Scale: 1/12 Reference: DCL-MSK021 Item: Ducati Superleggera V4 Includes: ..

WindshieldFamily: Vacuum formed parts Scale: 1/12 Reference: DCL-VAC006 Item: Ducati Desmosedici GP4 Race: Motorcycle World Championship 2003 Includes: vacuum formed parts To be used with: Tamiya reference TAM14101..

WindshieldFamily: Vacuum formed parts Scale: 1/12 Reference: DCL-VAC002 Item: Ducati 1199 Panigale S To be used with: Tamiya references TAM14129 and TAM14132..

Set of hood latches with pin for 1/12 scale models. Includes a total of 12 closures made of resin by 3D printing. It includes 4 different positions of the closure lock so that you can give more realism to your models, by not repeating the same configuration in all the closures.Family: Bonnet pins ..

Kit contains: - chain with sprockets (precut and ready for painting), - front sprocket screw (printed on sprocket), - set of rear sprocket nuts (printed on sprocket)...

Set of 24 inflation valves angled at 90, in 1:12 scale, produced using 3D printing, which faithfully reproduces this type of valves increasingly used in modern motorcycles. With the usual quality of Decalcas products, and the convenience of not requiring the use of primer, avoiding the loss of detai..

In conjunction with the release of two different versions of the 1/12 Scale Yamaha YZR-M1 Tamiya presents this compatible Front Fork Set including highly detailed parts to help you achieve that expert-level finish.Set includes the following parts Front Forks. Made from anodized aluminum for reali..

..

..

Type: water-slide decalsHow to apply water-slide decals:1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.2. Cut out the decal you need (do it on cutting m..

..

..

..

..

..

..

Water-slide Decals: Instruction: 1.Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them. 2.Cut out the decal you need (do it on cutting mat) 3.Grab the decal wit..

Water-slide Decals: Instruction: 1.Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them. 2.Cut out the decal you need (do it on cutting mat) 3.Grab the decal wit..