Model Planes

**NOTE:Slight warpage might occurred to the malleable nature of white metal and is easily straightened. A brief but succinct tutorial for working with white metal can be found on the homepage the their official website: www.scaleaircraftconversions.com..

LF-107 Lunak glider (Admiral kit)PE parts for Admiral-AZ kit..

#NOTE: The set does NOT include an aircraft model kit...

Letov S-328 (KP-Smer kit)PE set for KP-Smer kit..

Letov S-16 (Brengun kit)PE set for Brengun kit..

..

Paint Mask:Preparing the masks: Masks should not be stretched during the application process as they are flexible and this could cause deformation. Remove the whole mask if necessary, and then apply again. Once placed on the model, the mask surface should be adjusted to the surface of the model ..

Paint Mask:Preparing the masks: Masks should not be stretched during the application process as they are flexible and this could cause deformation. Remove the whole mask if necessary, and then apply again. Once placed on the model, the mask surface should be adjusted to the surface of the model ..

Set of four (4) 3D printed launchersThe LAU-7F/A was first introduced in 2008, with more widespread use by 2010. This version is used primarily on USMC F/A-18C/D aircraft...

Set of four (4) 3D printed launchersIn February of 1964, the LAU-7A/A was introduced as a USAF version of the LAU-7/A that incorporated provisions for launching the TDU-11/B Target Rocket.The LAU-7A/A was used interchangeably with the Aero-3B on USAF F-4C/D/E Phantoms.The standoff adapters in ..

Set of four (4) 3D printed launchersIn January of 1987, AAC-829 was introduced and by May of 1988, over 6500 launchers had been modified to LAU-7/A-6.Over the course of the next several years, numerous AAC's changed the designation of the launcher to B/A, A-7, B/A-1, as well as a few others. How..

Set of four (4) 3D printed launchersIn September of 1976, AAC 688 introduced a new dual Fin Retaining Clip for the new AIM-9L Sidewinder, creating the LAU-7/A-4.In June of 1980, AAC-736 was introduced and the launcher became the LAU-7/A-5.The LAU-7/A-5 was the launcher used when two VF-41 F-14..

Set of four (4) 3D printed launchersIn May of 1969, AAC 545 introduced the Fin Retaining Clip for the AIM-9D/G/H Sidewinder, creating the LAU-7/A-1.In January of 1971, AAC-537-1 introduced the Detent Holdback Pin, creating the LAU-7/A-2.By 1972, the launcher was re-designated as the LAU-7/A-3 ..

Set of four (4) 3D printed launchersThe LAU-7/A was developed in June of 1958 for use on the F4H-1 (F-4B) and designed to be used with the AIM-9B missile. This version was in service until May of 1969 when AAC-545 was introduced.Our sincere thanks to Gerry Whiteside and Bill Arndt for their ass..

72023 LAU-7 Missile Launcher (V2) by Tornado GR4/IDS/ECR, HAF F-4E AUP, GAF F-4F Phantom II etc. for 1/72 kit..

72024 LAU-7 Missile Launcher (V3) by F-14 Tomcat, AV-8B Harrier II, F/A-18 Hornet, etc. for 1/72 kit..

72035 LAU-5003 (19 tube) CRV7 70 mm Rocket Launcher as used by RAF Harrier GR7/9, RCAF CF-5, CF-18 and RNZAF A-4K for 1/72 kit..

72034 LAU-5002 (6 tube) CRV7 70 mm Rocket Launcher as used by RAF Harrier GR7/9, RCAF CF-5, CF-18 and RNZAF A-4K for 1/72 kit..

This set includes four (4) missile launchers in medium gray 3D printed resin.Missiles come as shown with print supports removed. Some very minor sanding to smooth areas where supports were located may be necessary.Launchers designed by Richard VanZandt of Flight Line Resin..