Model Planes

Set of four (4) 3D printed launchersThe LAU-7/A was developed in June of 1958 for use on the F4H-1 (F-4B) and designed to be used with the AIM-9B missile. This version was in service until May of 1969 when AAC-545 was introduced.Our sincere thanks to Gerry Whiteside and Bill Arndt for their ass..

3D printed resin. Comes on printing supports which need to remove...

Set contains photo etched parts/clear film#NOTE: The set does NOT include an aircraft model kit...

Set includes six (6) Mk-82/BLU-111 bombs with KMU-572 tail assemblies and nose strakes attached.Also included are six (6) DSU-33 proximity fuzes, six (6) MXU-735 solid nose plugs and six (6) Ogive nose plugs...

Set includes six (6) Mk-83/BLU-110 bombs with KMU-559 guidance kit and tail assemblies attached.Also included are six (6) each of the following : DSU-33 proximity fuzes, MXU-735 solid nose plugs and Ogive nose plugs...

The FPU-6/A Oval Fuel Tank was developed for the F/A-18A/B Hornet in 1978 and used on the FSD aircraft, as well as a few fleet Hornets into the mid 1980's. It was phased out due to fatigue anomalies caused by the oval configuration.This set includes two hollow tanks that require assembly. Some li..

3D printed resin. Comes on printing supports which need to remove...

Set FL172-2001 contains four correct SUU-63C/A wing pylons and one correct SUU-62C/A centerline pylon for the F/A-18A++, C and D.These pylons are correct for F/A-18C and D aircraft with BuNo's 163985 thru 165532 and aircraft upgraded to F/A-18A++ standard. The F/A-18A++ can be easily identified by..

This set includes correctly shaped and sized LEX Fence parts applicable to all 1/72 F/A-18A/B/C/D Hornet kits...

Set FL172-2000 contains four correct SUU-63/A wing pylons and one correct SUU-62/A centerline pylon for the F/A-18A and B.They not only correct the shape of the kit pylons, they provide details unmatched by the kit supplied parts. All pylons are 3D printed and require little clean up to remove the..

This item includes 2 sets of stiffening plates applied to the left side of each vertical tail on F/A-18A/A+ aircraft in use by the USN, USMC, Canada, Australia and Spain.Made of self adhesive vinyl, they will work with both Academy and Hasegawa 1/72 Kits...

Designed to be used with the Hasegawa kits, this is a simple to use and inexpensive way to replicate the strap applied to the bottom of the fuselage. Should also work with Fujimi and Revell Phantom kits...

Redesigned set includes the plates added to the upper wing and forward nose section. Parts adjusted to accurately fit all 1/72 F-16 kits...

Contains 1 resin part..

Photo etched stainless steel..

Includes PE parts..

#NOTE: The set does NOT include a plane model kit. Contains stainless steel PE & resin parts. Includes 3 different wheels..

Vinyl..

It contains 10 resin parts...

Note: This set does NOT include any aircraft kit.The set contains 8x resin parts...

The FMV Mod fitted to the tail boom of the AH-1Z and UH-1Y allows grounds units to see what the aircrew sees through the aircraft's FLIR.Designed for the Dream Model AH-1Z kit..

Designed by Jason Liang, this new set corrects the horribly inaccurate TSS provided in the kit.Modification of the kit part will be needed to use this item...

This set includes three (3) ADM-141 TALD.The TALD was used with great success on SEAD missions in the opening stages of Operation Desert Storm in 1991. More than 100 were launched on the opening night of the war. This prompted the Iraqi air defense to activate many of its radars most of which wer..

Vinyl Mask..