Model Planes

3D Scanned & Designed10 Resin PartsOptional 2 Heads..

3D Scanned & Designed 9 Resin Parts / Optional 2 Heads..

3D Scanned & Designed7 Resin Parts..

Type: water-slide decalsHow to apply water-slide decals:1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.2. Cut out the decal you need (do it on cutting m..

This is a full-length resin exhaust and nozzle set with the specific detail for EA-6B Prowlers which have an upgraded engine and different nozzle to the A-6 Intruder family. The instructions are based on fitting it to the Kinetic/Italeri kits, but the modeller may be able to adapt them to the Revell..

Including 2 seats 6 Resin, 14 PE parts..

for AFV Club 14 Resin/ 15 PE parts..

This is an early, plain fin cap without any RHAW or ECM pods as used on early F-4B (and C). Designed as a drop in replacement part for the Tamiya kit...

Detail parts for the inner canopies on F-4 Phantoms. The set comprises of resin and PE parts for windscreen, forward-, centre- and rear canopies and includes canopy actuator jacks, safety uplocks (optional installation), detailed downlocks, forward and rear compasses and various detail parts for the..

These are 3D printed face curtain handles for MB Phantom ejection seats. The handles are mainly designed for the Hypersonic Models Mk. H5 seats but can be used on other types (H7) and manufacturer's seats as well. The handles are 3D printed but from a slightly elasctic resin that doesn't break as ea..

This is an empty SR-71 brake chute bay with open doors, as commonly seen after landing. Designed specifically for the Revell kit. The set comes in four 3D printed parts: the main bay, a separate end cap (for easier painting) and separate doors. The door parts have mounting lips and recesses designed..

This set contains the parts needed to build an accurate late type F-104A from the Kinetic F-104A/C kit. "Late" means that it's an airframe that was converted to the upward firing C-2 seat. Therefore you can either use the kit supplied seat or one of the various available aftermarket options.The pa..

This is a set of highly detailed and appropriately proportioned stick/grip and throttle for the Kinetic F-104 kits in 1:48. The kit parts are both oversized and a bit sparse in detail. These 3D printed resin parts are drop-in replacements that fit right into the kit's mounting holes. The parts fit b..

This is a set of highly detailed and appropriately proportioned stick/grip and throttle for the Kinetic F-104 kits in 1:48. The kit parts are both oversized and a bit sparse in detail. These 3D printed resin parts are drop-in replacements that fit right into the kit's mounting holes. The parts fit b..

This is a set of two aft canopy braces for Kinetic F-104 Starfighter kits. This part is applicable to all F-104 single seat variants and is not provided in any of the Kinetic's kits. The part is very delicate, but printed from slightly forgiving resin for safer support removal and handling...

..

Type: water-slide decalsHow to apply water-slide decals:1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.2. Cut out the decal you need (do it on cutting m..

..

..

A set of two Martin Baker Mk. H5 ejection seats for early F-4B, F-4C and F-4D Phantoms (until around 1970). Suitable for and tested with Academy, Hasegawa and Zoukei Mura kits. The seats have cast on seat belts which differ from each other...

Dewoitine D.520, No.73/10 flown by Adj Andre Carrier of 2 Escadrille, GC I/3 Armee de L'Air, Wez-Thuizy, May 1940. The pilot lost his life in this aircraft on 14 May 1940...

Dewoitine D.520 with 1AC. 1AC fought the Allies during the Syria-Lebanon campaign...

Type: water-slide decalsHow to apply water-slide decals:1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.2. Cut out the decal you need (do it on cutting m..