Model Planes

Set of four (4) 3D printed launchersIn January of 1987, AAC-829 was introduced and by May of 1988, over 6500 launchers had been modified to LAU-7/A-6.Over the course of the next several years, numerous AAC's changed the designation of the launcher to B/A, A-7, B/A-1, as well as a few others. How..

Set of four (4) 3D printed launchersIn September of 1976, AAC 688 introduced a new dual Fin Retaining Clip for the new AIM-9L Sidewinder, creating the LAU-7/A-4.In June of 1980, AAC-736 was introduced and the launcher became the LAU-7/A-5.The LAU-7/A-5 was the launcher used when two VF-41 F-14..

Set of four (4) 3D printed launchersIn May of 1969, AAC 545 introduced the Fin Retaining Clip for the AIM-9D/G/H Sidewinder, creating the LAU-7/A-1.In January of 1971, AAC-537-1 introduced the Detent Holdback Pin, creating the LAU-7/A-2.By 1972, the launcher was re-designated as the LAU-7/A-3 ..

Set of four (4) 3D printed launchersThe LAU-7/A was developed in June of 1958 for use on the F4H-1 (F-4B) and designed to be used with the AIM-9B missile. This version was in service until May of 1969 when AAC-545 was introduced.Our sincere thanks to Gerry Whiteside and Bill Arndt for their ass..

1/72 AIRCRAFT No.9Cockpit interior reproduced with pilot figure included. Shiden Kai" that modified the problems of Shiden, and made the main wing arrangement from the middle wing to the low wing. Reproduction of Shiden Kai Type 21 with a large vertical tail fin area...

This is a plastic model kit, which comes unassembled and unpainted. So glue, model paints and other basic modelling tools are additionally required...

3D printed resin. Comes on printing supports which need to remove...

Photo etched stainless steel #NOTE: The set does NOT include a model kit...

Set contains photo etched parts/clear film#NOTE: The set does NOT include an aircraft model kit...

This is a plastic model kit, which comes unassembled and unpainted. So glue, model paints and other basic modelling tools are additionally required...

Set includes six (6) Mk-82/BLU-111 bombs with KMU-572 tail assemblies and nose strakes attached.Also included are six (6) DSU-33 proximity fuzes, six (6) MXU-735 solid nose plugs and six (6) Ogive nose plugs...

Set includes six (6) Mk-83/BLU-110 bombs with KMU-559 guidance kit and tail assemblies attached.Also included are six (6) each of the following : DSU-33 proximity fuzes, MXU-735 solid nose plugs and Ogive nose plugs...

The FPU-6/A Oval Fuel Tank was developed for the F/A-18A/B Hornet in 1978 and used on the FSD aircraft, as well as a few fleet Hornets into the mid 1980's. It was phased out due to fatigue anomalies caused by the oval configuration.This set includes two hollow tanks that require assembly. Some li..

3D printed resin. Comes on printing supports which need to remove...

Set FL172-2001 contains four correct SUU-63C/A wing pylons and one correct SUU-62C/A centerline pylon for the F/A-18A++, C and D.These pylons are correct for F/A-18C and D aircraft with BuNo's 163985 thru 165532 and aircraft upgraded to F/A-18A++ standard. The F/A-18A++ can be easily identified by..

This set includes correctly shaped and sized LEX Fence parts applicable to all 1/72 F/A-18A/B/C/D Hornet kits...

Set FL172-2000 contains four correct SUU-63/A wing pylons and one correct SUU-62/A centerline pylon for the F/A-18A and B.They not only correct the shape of the kit pylons, they provide details unmatched by the kit supplied parts. All pylons are 3D printed and require little clean up to remove the..

This item includes 2 sets of stiffening plates applied to the left side of each vertical tail on F/A-18A/A+ aircraft in use by the USN, USMC, Canada, Australia and Spain.Made of self adhesive vinyl, they will work with both Academy and Hasegawa 1/72 Kits...

Designed to be used with the Hasegawa kits, this is a simple to use and inexpensive way to replicate the strap applied to the bottom of the fuselage. Should also work with Fujimi and Revell Phantom kits...

Redesigned set includes the plates added to the upper wing and forward nose section. Parts adjusted to accurately fit all 1/72 F-16 kits...

Contains 1 resin part..

Photo etched stainless steel..

This is a plastic model kit, which comes unassembled and unpainted. So glue, model paints and other basic modelling tools are additionally required.The De Havilland "Mosquito" made of wood was designed based on "high-speed bomber shaking off fighter". The design of the Mosquito was got in shape in 1..

Includes PE parts..