Print Scale 48-057 1/48 Yakovlev Yak-9 Fighter Decals

Type: water-slide decals

1. Yak-9U - flown by Georgiy Baevski, Hero of the Soviet Union (19 personal victories). The 5th Guards Fighter Regiment (GIAP),
Germany, March 1945.

2. Yak-9P (Yak-9B) ?Moscow? - tactical number ?2" - flown by Captain I.I. Petrov, the commanding officer of the 1st Sq. 168th IAP. Khimki, Moscow, June 13, 1944.

3. Yak-9M - flown by soviet ace pilot G.L. Nakaznyuk. (5 personal and 5 group victories. Participated in 60 aerial combat in 78 sorties). This a/c was flown Nakaznyuk from August 1944 and shot down a Fw-190. The aircraft was gray on all surfaces. The emblem of the Orden of the Battle Red Banner was only on the port side.

4. Yak-9D, tactical number 31 - flown by Vladimir I. Voronov, the wingman of M. Grib. The 6th GIAP of the 11th ShAD, Black Sea Fleet Arm, May 1944.

5. Yak-9D - tactical number 22 - flown by Captain M. Grib (17 victories). The 6th GIAP of the 11th ShAD, Black Sea Fleet Arm, Saki Airfield, April-May 1944.

6. Yak-9T - tact.# 38 - flown by Lieutenant Alexandr I. Vybornov, Commander of the 3rd sq. 728 IAP, 3 IAK, 256 IAD. (20 victories) Poland, autumn 1944.

7. Yak-9UT - tact.number 1 ?Pobeda? - flown by Captain Garry Merkveladze, Hero of the Soviet Union, deputy squadron commander in the 152nd Sandomir, Bogdan Khmelnitski and Alexander Nevski Orders GIAP, 12 GIAD. (13 personal and 2 group victories) Prague, Czechoslovakia, May 1945

8. Yak-9T - tact.# 52 - flown by Lieutenant Petr Peskarev. The 812th IAP. This a/c was shot down on April 12, 1944 - pilot KIA.

9. Yak-9P of North Korean Air Force. This a/c was captured by the US troops at ?Kimp-Ho? airfield.

10. Yak-9UT - tact.# 31 - belonged to the 3rd sq. of the 43rd, IAP, 3 IAK, 16VA. East Prussia, May 1945.

11. Yak-9U - tact.# 2, ser. N. 42166097 - flown by Lieutenant N.F. Kizim, the 2nd sq. Yambol Airfield, Bulgaria, 1945-1946.

How to apply water-slide decals:
1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.
2. Cut out the decal you need (do it on cutting mat)
3. Grab the decal with tweezers, place it on the surface of the water and leave it for about 20 seconds.
4. Remove the decal from the water and place it on paper towel to remove any excess water.
5. Apply decal solution to the part where the decal is to be placed.
6. Slide the decal off the backing paper on to the model. Using a paint brush or cotton bud is a good way to do this without damaging the decal.
7. Use the brush, knife or cotton bud to position the decal. Using your paper towel, gently dab the decal and soak up the excess water (decal softner is also recommended at this stage. After applying softner, the decal will suction to the part and flatten out smooth.)
8. When the decal is completely dry, give another coat of varnish or Klear/Future to seal it.