Print Scale 72-111 1/72 Cessna A/T-37 Dragonfly Decals
Type: Water-slide decals
1. !essna A-37B Dragonfly of the 524th Fighter Squadron, 62nd Tactical Wing 2nd Air Division located at Nha Trang during 1969. The A-37B gradually replaced the A-1 as the VNAFs main fighter-bomber.
2. !essna A-37B Dragonfly of the 516th Fighter Squadron,41st Tactical Wing, 1st Air Division based at Da Nang during June of 1970. The A-37s was developed especially for small air forces like the VNAF and was simple to maintain and operate.
3. !essna A-37B Dragonfly Part: Escuadron de Caza-Bombardeo 711/712, FAP No. 151 A-37 attack planes took an active part in the war of 1995.
4. !essna A-37B Dragonfly (69-6359) of the 8th SOS, 14th SOW based at Bien Hoa Air Base , Vietnam, during 1970.
5. The Vietnamese Air Force (VNAF) flew large numbers of A-37Bs, including this Dragonfly of the 520th Fighter Squadron based
at Binh Thuy Air Base.
6. T-37A-CA 56-3464 was evaluated by the U.S. Army during the HPAOA trials held during the late 1950.
7. This T-37B-CE (58-7982) of the 38th FTW carries the standard trainer scheme used during the 1970s and 1980s and has an Air Force Outstanding Unit Award ribbon painted on the fin.
8. T-37Bs assigned to the 507th TACW carry the wrap-around ??Lizard?? cam
How to apply water-slide decals:
1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.
2. Cut out the decal you need (do it on cutting mat)
3. Grab the decal with tweezers, place it on the surface of the water and leave it for about 20 seconds.
4. Remove the decal from the water and place it on paper towel to remove any excess water.
5. Apply decal solution to the part where the decal is to be placed.
6. Slide the decal off the backing paper on to the model. Using a paint brush or cotton bud is a good way to do this without damaging the decal.
7. Use the brush, knife or cotton bud to position the decal. Using your paper towel, gently dab the decal and soak up the excess water (decal softner is also recommended at this stage. After applying softner, the decal will suction to the part and flatten out smooth.)
8. When the decal is completely dry, give another coat of varnish or Klear/Future to seal it.
1. !essna A-37B Dragonfly of the 524th Fighter Squadron, 62nd Tactical Wing 2nd Air Division located at Nha Trang during 1969. The A-37B gradually replaced the A-1 as the VNAFs main fighter-bomber.
2. !essna A-37B Dragonfly of the 516th Fighter Squadron,41st Tactical Wing, 1st Air Division based at Da Nang during June of 1970. The A-37s was developed especially for small air forces like the VNAF and was simple to maintain and operate.
3. !essna A-37B Dragonfly Part: Escuadron de Caza-Bombardeo 711/712, FAP No. 151 A-37 attack planes took an active part in the war of 1995.
4. !essna A-37B Dragonfly (69-6359) of the 8th SOS, 14th SOW based at Bien Hoa Air Base , Vietnam, during 1970.
5. The Vietnamese Air Force (VNAF) flew large numbers of A-37Bs, including this Dragonfly of the 520th Fighter Squadron based
at Binh Thuy Air Base.
6. T-37A-CA 56-3464 was evaluated by the U.S. Army during the HPAOA trials held during the late 1950.
7. This T-37B-CE (58-7982) of the 38th FTW carries the standard trainer scheme used during the 1970s and 1980s and has an Air Force Outstanding Unit Award ribbon painted on the fin.
8. T-37Bs assigned to the 507th TACW carry the wrap-around ??Lizard?? cam
How to apply water-slide decals:
1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.
2. Cut out the decal you need (do it on cutting mat)
3. Grab the decal with tweezers, place it on the surface of the water and leave it for about 20 seconds.
4. Remove the decal from the water and place it on paper towel to remove any excess water.
5. Apply decal solution to the part where the decal is to be placed.
6. Slide the decal off the backing paper on to the model. Using a paint brush or cotton bud is a good way to do this without damaging the decal.
7. Use the brush, knife or cotton bud to position the decal. Using your paper towel, gently dab the decal and soak up the excess water (decal softner is also recommended at this stage. After applying softner, the decal will suction to the part and flatten out smooth.)
8. When the decal is completely dry, give another coat of varnish or Klear/Future to seal it.
| General Info | |
| Scale | 1/72 |
| Type | Model Upgrade/Accessory |
| Subtype | Decals / Stickers |
- Stock: In Stock
- Reward Points: 19
- SKU: PRS72-111
- 1pcs in Stock
Print Scale
MRP: US$18.68 Save: US$5.85
31% OFF
US$12.83
(excl. Tax)
"In-Stock" Really Means It
Combine Shipping & Save
SAME or Next day shipping*
There are no reviews
Maybe you can help? Many users will be grateful to you. And so are we.